Description

Portable Dental Unit with Air Compres s or Technical data Model:BD-406 Portable Dental Unit Votalge: 110 V/60Hz, Power: 600 W Air Flow:130L/min Pressure:0.8Mpa Net Weight:2 9 Kgs Gross Weight:3 4 Kgs Noise:40dB Packing Size: 56*42*76 cm Note: This product is only suitable for 110V voltage, please do not use 220-240V voltage, as 220-240V will cause the machine to burn out. Standard Accessoiries ： Oiless Air Compressor Motor 1pc 3 Way-Springe 1pc High Speed Handpiece Pipe 1pc Low Speed Handpiece Pipe 1pc Built in Ultrasonic Scaler 1pc Built in LED Light Curing Unit 1pc High Suction(Ajust) 1pc 6L Air Tank 1pc Water Bottle 1pc Drain Bottle 1pc Foot Control 1pc Safety Guidelines 1, Before operating the unit, please read the manual carefully and preserve it for future reference. 2, Please operate and maintain the unit strictly in accordance with the operational instructions. 3, The user should read the instructions supplied with the dental unit carefully. 4, Symbol “Attention” denotes that before using the device, read the operating manual carefully and carry out all the instructions to avoid any damage or injury. 5, Please contact the local agent or the manufacturer if the unit needs repairs. We will supply a high quality of service and assistance for you. Warning: 1 The power switch should be turned off when the machine stopped working, the transformer and solenoid valves will heat to burn if long-term power or no stop the power. 2. Please drain off the water when the water on 2/3 of Suction bottle, the water will come to motor if the water is higher than 2/3 on suction bottle, the air motor will leakage of electricity or burn if the water come to air motor. [NOTE] :Both 4 Hole and 2 Hole are available, we send 4 Hole by default! If you neee 2 Hole, please leave us a message, we will send you the right one! X-Ray Sensor Size:1.0 /2.0 Dental Sensor X-Ray Digital Sensor Intraoral Digital System HD Image Dentistry Tools Feature: 1. If there’s only one device, you may select “Single-User” installation. If the sensor is connected to multiple device, select “Host” for the device connected with the sensor and other devices select “Extension” to install, to achieve multi-machine sharing. 2. The sensor is available in two sizes, with rounded corners and a thickness of only 4.4mm, making it more comfortable to use. 3. Cables are durable ， have been tested for 80,000+ bends. 4. CMOS detector technology with CSI scintillator. Ensures optimal resolution Low dose clinical imaging. 5. Compatible with different X-ray generators, easy to use. 6. No consumables and more cost-effective than traditional film. Hardware and software requirement ： Processor ： 1.0GHz or above Memory ： 2GB or above Hard disk ： 64GB or above Display resolution ： 1440*900 or above USB port ： USB2.0 Operating system ： Windows 7 、 Windows10 、 Windows11 Technical parameter ： S1 S2 Detector Technology APS CMOS APS CMOS Scintillator CsI CsI Theoretical Resolution 25lp/mm 25lp/mm True Resolution 20lp/mm 20lp/mm Pixel Matrix 1000*1500 1300*1800 Active Area(mm) 20*30 26*36 Mechanical Size(mm) 25.4*38.2*4.4 30.4*44*4.4 Data interface USB 2.0 USB 2.0 AD Conversion(bit) 16 16 Protection IP68 IP68 Packing list ： 1. Sensor 2. USB flash disk (Software) 3. Protective sleeve Dental x-ray machine. AZdent Portable dental X-ray machine,High Frequency x-ray machine compatible with digital sensor and x-ray film. FEATURE ： 1. Compatible with digital sensors, X-ray film, and image plate scanners. 2. Small and portable. 3. This portable dental X-ray machine is high frequency machine. 4. The body is small, light in weight, and the radiation leakage is less than 20μgy/h. 5. It has excellent image quality, portable storage, save more space. 6. It uses high frequency and DC international power supply. 7. All of the components installed in the central PC board concentrated. Shock,set-up, electron tubes, all of them are insulation vacuum, sealed stereotype protection. 8. Different exposure times are preset for adults and children. 9. The battery is durable, it can take about 4 hundred images after fully charged. TECHNICAL SPECIFICATIONS ： 1. Tube voltage ： 60KV 2. Tube current ： 2mA 3. Exposure time ： 0.1-2.0S 4. Frequency ： 30kHz 5. Rate power ： 120VA 6. Distance from skin to cone ： 105mm 7. Tube focus ： 0.8mmx0.8mm 8. Battery ： DC14.8V 1600mAh 9. Charger input voltage ： AC100V-240V+10% 10. Output voltage ： DC16.8V 11. Ambient temperature ： 5℃~40℃ 12. Relative temperature ： <75%RH